 |
 |
|
 |
|
| Author |
Message |
silverfoxx03
Community Member
Joined: 13 Jun 2007
Posts: 11
Location: Michigan
|
 Posted: Tue Apr 20, 2010 6:50 pm Post subject: Necromonger Dagger |
 |
|
I am offering these elsewhere but wanted to offer them up here as well. I am getting set to do a run of these
Riddick concluded that the prized dagger of a Necromonger was
"a half gram too heavy on the back end" after an inspection lasting all of a couple of seconds
I did an average weight and these are approximately 389 grams allowing for deviation on material
(Offering modified due to requests)
I am considering doing a run of these. This was done from a rubber Stunt that was actually used in the movie. I had permission from the owner and he sent me the Stunt to use.
These will be of cold cast metal/resin
They will come with the locking display case also as shown . The plaque will be brass.
(I have a paper plaque in there just to show the effect.)
I am looking for interest right now. I would need 20 or more people committed to go ahead with these in any combinations of the following.
ONE-SIDED with display case and plaque
2 sided full Cold Cast Metal with Display case and plaque
2 sided full Cold Cast Metal -No display or plaque
2 sided full resin-no finish, display or plaque
Specify the codes listed when responding
Prices will be as follows:
NK1 One sided in Display case and plaque -$150.00 +shipping
NK2 Two sided in Display Case and plaque-$175.00 + shipping
2CC Two sided cold cast knife only-no case or plaque -$100+shipping
2R Two sided resin only -no finish-$75.00+shipping
http://propsummit.com/upload/257/riddick1.jpg
http://propsummit.com/upload/257/riddick2.jpg
http://propsummit.com/upload/257/riddick3.jpg |
|
| Back to top |
|
|
|
|
 |
|
 |
|
|
|
|
| Author |
Message |
silverfoxx03
Community Member
Joined: 13 Jun 2007
Posts: 11
Location: Michigan
|
| Posted: Fri Apr 23, 2010 5:26 am Post subject: Necromonger Dagger |
|
|
| No takers here?? |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| Author |
Message |
clutch
Community Member
Joined: 12 Dec 2006
Posts: 548
|
| Posted: Fri Apr 23, 2010 9:05 am Post subject: |
|
|
No necromongers in Blade Runner.  |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| Author |
Message |
Marishvcard
Joined: 02 Jun 2012
Posts: 2
Location: 2846 Cessna Drive
|
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| Author |
Message |
Noeland
Community Guide
Joined: 24 Oct 2006
Posts: 1328
|
| Posted: Sat Jun 02, 2012 2:12 pm Post subject: |
|
|
The Furian necromonger was based on Roy Batty. That's a little something.
_________________
I don't have enough blasters! |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
|
|
